Sold
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
i have attached some of the requested pics, more to come
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
heidi just showed up with the bars, cheers mate.
she accidentally handed over too much money and kei_spec rang her to come back for it. much respect goes his way
she accidentally handed over too much money and kei_spec rang her to come back for it. much respect goes his way
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
Prices updated, will now separate engine and box
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
- mini_kompressor
- Posts: 322
- Joined: Sun Jan 13, 2008 8:00 pm
Fitted the steering wheel today aty lunch, looks great, cheers Mark
are they 4wd box's or just front wheel drive?
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
The boxes are f6a FWD, i have modified a alto shifter to fit one of them so whoever buys the first box gets the shifter setup and i will throw in a nearly new clutch cable and the starter motor to suit.
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
so anyone know if it would bolt to an F8b? i think it will just wantin to confirm
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
the shafts have female inners, my custom shafts are the same length as 87 alto so if alto shafts fit a mb???,then my shafts will fit
can supply flywheel and clutch to suit for $50
can supply flywheel and clutch to suit for $50
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
UPDATE2X tiny tdo4 turbos off mitsubishi gto 3000gt (probably good for 800cc-1.5ltr engine??) 3 bolt turbine housing flange, dump pipe included.
$175 each
Chevoit 14"x6" rims with 175/65/14+ 185/65/14 tyres 4x114.3 stud pattern $180 set.
$175 each
Chevoit 14"x6" rims with 175/65/14+ 185/65/14 tyres 4x114.3 stud pattern $180 set.
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto
what is the the bolt spacing on the exhaust flange on the td03's????
Also i'm assuming they are the 9b's not the 13g's???
Also i'm assuming they are the 9b's not the 13g's???
[url=http://www.tamon.org/gallery/v/members/ike849/][img]http://www.tamon.org/forum/images/per_gall.gif[/img][/url]
- kei_spec_rsr
- Posts: 106
- Joined: Thu Apr 23, 2009 11:08 am
- Location: sydney
dont know what size exhaust housing, looks pretty small. bolt spacing is uneven 52mm,62mm,65mm. compressor housing inlet 35mm
Parting out the alto
Need it all gone asap
wrecking cc72v alto
Need it all gone asap
wrecking cc72v alto